|
Courtesy of Brian Gibbs, we have instructions and even a parts list for putting together your own portable setup for events tabling.
Note that there is a download link for a (large) PDF at the bottom of the page.
Dept of Peace Tabling Lite Kit – Sit Down Model
(banner bottom height from ground-5’3”)
Dept of Peace Tabling Lite Kit – Stand Up Model
(banner bottom height from ground-5’11”
or 6’6”)
Note: For typhoon conditions, anchor gallon
jugs of water (or milk) to table legs with bungee cords and hold onto table to prevent getting blown
away. If you get blown away, at least it was for a good cause.
Dept of
Peace Tabling Lite Assembly Instructions
By Brian
Gibbs (7/2/08)
Note: The below instructions refer to parts that can be
seen in the DoP Tabling Lite Parts List after
this section. The instructions 1 thru 14 refer to assembling the Sit Down model
(banner bottom height from ground-5’3”).
To construct the Stand Up model (banner bottom height
from ground-5’11” or 6’6”), implement instruction 15.
|
Instruction
|
Visual
|
- Drill a hole using a 7/64” drill bit so you can screw Part D (1 ½
“ hook) into Part E (21.5 inch long piece of ¾ “ PVC pipe). Place 1
1/8” from the end of Part E.
|
|
- Drill a ¾” hole into each corner of the rear of the table (See Part
K visual below).
|
|
- Place Part G (32 inch long piece of ¾” PVC pipe) into each of these
¾” holes you just drilled with table legs upright.
|
|
- Attach Part H (¾” PVC pipe connector) to each Part G (32 inch long
piece of ¾” PVC pipe) that rises above the table top.
|
|
- Attach the two remaining Part G (32 inch long piece of ¾” PVC pipe)
to each Part H (¾” PVC pipe connector).
|
|
- Attach Part F (¾” x ½” x ¾” T joint) to the top of each Part G (32
inch long piece of ¾” PVC pipe) above the table with each ½” connector
facing each other..
|
|
- Attach horizontal Part C (43 inch long piece of ½” PVC pipe) to each
Part F (¾” x ½” x ¾” T joint).
|
|
- Attach Part E (21.5 inch long piece of ¾ “ PVC pipe) to each Part
F (¾” x ½” x ¾” T joint). The end with Part D (1 ½ “ hooks) should
be the farthest from the ground. The hooks should be facing towards
the front of the table.
|
|
- Attach Part B (½ “ by ¾ “ elbow) to each Part E (21.5 inch long piece
of ¾ “ PVC pipe) with each ½” connector facing each other.
|
|
- Attach the remaining Part C (43 inch long piece of ½” PVC pipe) to
each Part B (½ “ by ¾ “ elbow).
|
|
- Place top of banner eyeholes into each Part D (1 ½ “ hooks).
|
|
- Swivel Part E (21.5 inch long piece of ¾ “ PVC pipe) outward which
contains the Part D (1 ½ “ hooks) so that sufficient horizontal tension
is maintained at top of banner.
|
See below
|
- Attach one end of Part L (8” bungee cord) to eyeholes at bottom of
each banner corner and then wrap bungee cord around Part G (32 inch
long piece of ¾” PVC pipe) three times right underneath Part F (¾”
x ½” x ¾” T joint) and secure other end of Part L (8” bungee cord)
to eyeholes at bottom of banner.
|
|
- Wrap the two remaining Part L (8” bungee cord) around the bottom
of each table leg and around each Part G (32 inch long piece of ¾”
PVC pipe) and secure so that each Part G under the table is anchored
to each table leg.
|
|
- To create a Stand Up model, use Part H (¾” PVC pipe connector) and
either Part I (8 inch long piece of ¾” PVC pipe) to create a standing
height of 5’11” or Part J (15 inch long piece of ¾” PVC pipe) to create
a standing height of 6’6”. Attach the desired parts to the bottom of
each Part G (32 inch long piece of ¾” PVC pipe) which is resting under
the table against the ground. This will extend the height of the banner
to allow stand up conversations to occur.
|
|
DoP Tabling Lite Parts List
By Brian
Gibbs (7/2/08)
|
Part
|
Item Picture
|
Description
|
Qty
|
Placement or General Comments
|
Cost
|
|
A
|
|
Dept of Peace Banner -
46”(W) X 22”(H)
|
1
|
It was obtained from the
vendor references on The Peace Alliance's website. The ordering
page is at https://www.bizopguy.com/dop1.htm.
It is listed as a 4’ by 2’ banner, but is actually 46”(W) by
22”(H).
|
$64
|
|
B
|
|
½ “ by ¾ “ elbow
|
2
|
Connects to vertical Part E (21.5 inch long piece
of ¾ “ PVC pipe) and horizontal Part C (43 inch long piece of ½” PVC
pipe).
|
$1.30 for 2
|
|
C
|
|
43 inch long piece of ½” PVC pipe
|
2
|
Connects to Part B (½ “ by ¾ “ elbow) and Part F (¾”
x ½” x ¾” T joint).
|
$1.81 for 10’ section
|
|
D
|
|
1 ½ “ hooks
|
2
|
Screwed into vertical Part E (21.5 inch long piece
of ¾ “ PVC pipe).
|
98 cents for a bag of 2
|
|
E
|
|
21.5 inch long piece of ¾ “ PVC pipe
|
2
|
Connects to Part B (½ “ by ¾ “ elbow) and Part F (¾”
x ½” x ¾” T joint).
|
$4.64 for two 10’ sections
|
|
F
|
|
¾” x ½” x ¾” T joint
|
2
|
Connects to vertical Part E (21.5 inch long piece
of ¾ “ PVC pipe), horizontal Part C (43 inch long piece of ½” PVC pipe),
and vertical Part G (32 inch long piece of ¾” PVC pipe).
|
92 cents for 2
|
|
G
|
|
32 inch long piece of ¾” PVC pipe
|
4
|
Connects to Part F (¾” x ½” x ¾” T joint) and Part
H (¾” PVC pipe connector)..
|
See Part E costs above.
|
|
H
|
|
¾” PVC pipe connector
|
4
|
Connects to vertical Part G (32 inch long piece of
¾” PVC pipe).
|
80 cents for 4
|
|
I
|
|
8 inch long piece of ¾” PVC pipe
|
2
|
Extend banner bottom height
from ground to 5’11”. Connects to Part H (¾” PVC pipe connector).
|
See Part E costs above.
|
|
J
|
|
15 inch long piece of ¾” PVC pipe
|
2
|
Extend banner bottom height
from ground to 6’6”.
Connects to Part H (¾”
PVC pipe connector).
|
See Part E costs above.
|
|
K
|
|
4’ x 2’ composite table
|
1
|
Good lightweight table
that matches up well with DoP banner width. (This table in addition
to the other parts described, excepting the DoP banner, were obtained
from Home Depot.)
|
$39.87
|
|
L
|
|
8” bungee cords
|
4
|
Straps bottom of DoP banner
to vertical Part G (32 inch long piece of ¾” PVC pipe). Also,
straps Part G to base of table legs for anchoring purposes.
|
$2.29 for pack of 8
|
DoP Tabling
Lite Kit ready for travel
Download:
You can download a PDF of these instructions by  clicking here 2.07 Mb.(Windows users can also right click and select "Save Link As")
|
